CROSSOVER-RX AR3201-F2 receiver with dual 5A 1S brushed ESC

CROSSOVER-RX AR3201-F2 Receiver with Dual 5A 1S Brushed ESC

AR3201 is a kind of highly integrated receiver with two built-in 5A-1S brushed ESCs and DCDC-5A/1A boosting power. It is widely used for home-built or conversion of model airplanes and vehicles weighing between 25g and 100g.

The module requires a model control signal according to the M-BUS protocol and enables bidirectional motor control. The module also has 4 connectors with ELE, AIL, RUD and THR channels to control aileron, elevator, throttle and rudder.

It has 4 independent 1.00 mm micro JST-SH servo connectors and a 4P-M-BUS connector. Two Molex motor connectors with 1.25 mm plug and 2P are included, which can be soldered as an option. All Crossover RX receivers have a user-friendly, automatic binding system. They are compatible with many readily available rotary and linear digital servos with 1.00 mm micro JST-SH connectors.

Overview:

• Model: AR3201-F2(FR-D16)
• Small size: 22.0 x 16.0 x 6.2 mm (without antenna)
• Super light: 1.5 g (with antenna)
• Operating voltage: 3.0 to 5.0 V
• DCDC-5 V/1 A amplification power for servos
• With 2 integrated brush ESCs (5 A/1 S, start inhibit)
• Supports TELEM function (voltage message returns to transmitter, available on AR3201-A/D/F2 and AR3201G-A2/D/F2)
• Supports GUI setting function
• Supports differential speed mode
• eLE, AIL, RUD and THR connection
• Maximum current: 2 A
• M-BUS control signal
• Supports RSSI output
• Motor connection: Molex connector 2P with 1.25 mm pitch included, soldering possible.
• simple automatic binding program, many available protocols: Spektrum DSMX DSM2, Futaba SFHSS, FRSKY-D8, FRSKY-D16, Flysky AFHDS-2A and HOTT available soon.
• TELEM function: battery voltage, receiver voltage, signal strength, device temperature
• Servo connections: Micro JST-SH 1.00 mm spacing

Start-Lock function

The start-lock function is the integrated brush ESC function that prevents the brush motor from starting accidentally. It can protect the brush motor from starting even if the throttle is not in the lowest position when the receiver is switched on.
Once the receiver receives the signal and the throttle of your transmitter is in the lowest position for the first time for 2 seconds, the start-lock function will be released and the brush motor will run when the throttle is pressed.

Automatic binding:

The receiver automatically switches to bind mode after it receives power and does not receive a transmitter signal for 15 seconds. The slowly flashing blue LED light changes to a fast flashing light. The receiver is now in binding mode.

Gas range:

Simply start the receiver with the TX at maximum throttle. This will set the maximum throttle. Then pull back the throttle, which will set the minimum throttle. Calibration is now complete. You may need to lower your throttle trim all the way down for the ESC to detect zero throttle.

TELEM function (available on AR3201-A/D/F2 and AR3201G-A2/D/F2)

The TELEM function is useful for monitoring the battery voltage, the operating voltage of the receiver and its signal strength as well as its operating temperature in real time. This controls the operating status of the receiver and the discharge status of the battery, so that flying outside the control range and over-discharge rarely occur.

NOTE: The effective control range of the TELEM function depends on the transmitter. The range of the receiver is often much greater than the effective range of the TELEM function.

CrossOver-RX configuration tool:

The CrossOver-RX configuration tool is a firmware update tool for Crossover-RX products. Using the USB configuration tool and the GUI (graphical user interface) software listed below, you can access many programming options and available firmware updates for various Crossover RX products. The USB configuration tool is available with either a 3- or 4-wire M-BUS connection cable.

How to connect RX to the GUI software (with USB programmer MX-PG02):

https://store.mxo-rc.com/home/135-1217-crossover-rx-ar3201-ar3201g-v20-built-in2-brushed-escs6ch-microrxtelem.html#/41-type-flysky_a2/71-do_you_need_a_compiler-no/73-do_you_need_the_gyro_function-no/96-do_you_need_a_servo-no:~:text=How%20to%20connect%20RX%20to%20GUI%20software

Scope of delivery:

• 1x CROSSOVER-RX AR3201-F2 receiver with dual 5A 1S brushed ESC